Zenith P42W24B Manuel d'utilisateur télécharger pdf

1. Application Object

These instructions are applied to all of the PDP monitor, RF-

02RA.

2. Notes

(1) Because this is not a hot chassis, it is not necessary to use

an isolation transformer. However, the use of isolation

transformer will help protect test instrument.

(2) Adjustment must be done in the correct order.

(3) The adjustment must be performed in the circumstance of

25±5°C of temperature and 65±10% of relative humidity if

there is no specific designation.

(4) The input voltage of the receiver must keep 110~240V,

50/60Hz in adjusting.

(5) The receiver must be operated for about 15 minutes prior

to the adjustment.

1) After receiving 100% white pattern, the receiver must be

operate prior to adjustment.(Or white condition in HEAT-

RUN mode)

2) Enter into HEAT-RUN mode

- Select the HEAT-RUN OFF by pressing ADJ Key on

Remote Control for adjustment.

- Press the VOL + Key in HEAT-RUN OFF.

(OSD display HEAT-RUN WHITE and screen display

100% FULL WHITE PATTERN)

[ Set is activated HEAT-RUN without signal generator in

this mode.

[ Single color pattern of HEAT-RUN mode uses to check

PANEL.(RED/BLUE/GREEN)

[Caution] If you turn on a still screen more than 20 minutes, a

afterimage may be occur in the black level part of the

screen.

Each PCB Assy must be checked by the Check JIG Set before

whole assembly. (Be careful the POWER PCB Assy not to

damage to PDP Module)

3. POWER PCB Assy Voltage Adjustment

(Va, Vs, -Vy, Vsetup Voltage Adjustment)

3-1. Test Equipment

D.M.M 1EA

3-2. Connection Diagram for Measuring

Refer to Fig 1.

3-3. Adjustment Method(POWERWELL)

(1) Va Adjusment

1) Connect pin 1 of CN205 to (+) jack of D.M.M.

2) After turning the VR3(Va ADJ), voltage of D.M.M

adjustment as same as Va voltage which on label of

panel right/top.(Deviation : ±0.5V)

(2) Vs Adjustment

1) Connect pin 1 of CN207 to (+) jack of D.M.M.

2) After turning the VR6(Vs ADJ), voltage of D.M.M adjust

as same as Vs voltage which indicated on label of panel

right/top.(Deviation : ±0.5V)

(3) -Vy Adjustment

1) Connect pin 1 of CN208 to (+) jack of D.M.M.

2) After turning the VR5(-Vy ADJ), voltage of D.M.M adjust

as same as -Vy voltage which indicated on label of

panel right/top.(Deviation : ±0.5V)

(4) Vsetup Adjustment

1) Connect pin 5 of CN208 to (+) jack of D.M.M.

2) After turning the VR4(Vsetup ADJ), voltage of D.M.M

adjust as same as Vsetup voltage which indicated on

label of panel right/top.(Deviation : ±0.5V)

- 18 -

ADJUSTMENT INSTRUCTIONS

<Fig 1> Connection Diagram of POWERWEL Power Adj. for

Measuring

1 2 3 4 5 6 ... 16 17

Résumé du contenu

Page 1 - ADJUSTMENT INSTRUCTIONS

1. Application ObjectThese instructions are applied to all of the PDP monitor, RF-02RA.2. Notes(1) Because this is not a hot chassis, it is not necess

Page 2

- 27 -LOCA. NO PART NO DESCRIPTIONC612C613C614C615C616C618C621C624C625C627C628C629C630C631C633C634C

Page 3

- 28 -LOCA. NO PART NO DESCRIPTIONAR1703AR1704AR1705AR1706AR1707AR1708AR1709AR1710AR1711AR1712AR171

Page 4 - BLOCK DIAGRAM

- 29 -LOCA. NO PART NO DESCRIPTIONL1818L1819L1822L1823L1825L1826L1827L1828L1829L1830L1831L1832L1833

Page 5 - EXPLODED VIEW

Page 6 - EXPLODED VIEW PARTS LIST

Page 7

Page 8

Page 9

PRINTED CIRCUIT BOARDMAIN(TOP) MAIN(BOTTOM)SPK(TOP) SPK(BOTTOM) POWERAV FIX BOARD(TOP)A/V(TOP)A/V(BOTTOM)AV FIX BOARD(BOTTOM)CONTROL(TOP)CONTROL(B

Page 10 - REPLACEMENT PARTS LIST

- 19 -[ Refer to Typical Voltage1. Va : 35 ~ 45V2. Vs : 170 ~ 185V3. -Vy : -60 ~ -90V4. Vsetup : 210 ~ 240V[ Replace PDP Module or Power Board, adjus

Page 11

- 20 -5-2. Connection Diagram of Equipment forMeasuring[ After stop the Micom by pressing IN-START Key on RemoteControl, insert the P1002 with automa

Page 12

- 21 -BLOCK DIAGRAM

Page 13

- 22 -EXPLODED VIEW200203201202205204207208209206540401550310551520560570400410530580210301302300305

Page 14

- 23 -EXPLODED VIEW PARTS LIST200 6348Q-E034A PDP,42 16:9 852*480 LOW VOTAGE DRIVING201 6871QTH025A PCB ASSEMBLY,ZCNT ASSY HAND INSERT 42SD4 ZCNT TOP

Page 15

- 24 -REPLACEMENT PARTS LISTLOCA. NO PART NO DESCRIPTIONIC805IC806IC807IC901IC902IC903IC904IC905IC90

Page 16

- 25 -LOCA. NO PART NO DESCRIPTIONQ204Q205Q206Q301Q302Q303Q401Q402Q403Q404Q405Q406Q407Q408Q409Q410Q

Page 17 - PRINTED CIRCUIT BOARD

- 26 -LOCA. NO PART NO DESCRIPTIONC034C035C038C042C043C045C1110C1119C1131C1132C1133C1135C1147C1148C

Commentaires sur ces manuels

Pas de commentaire

Zenith P42W24B Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Téléviseurs et moniteurs Zenith P42W24B. ADJUSTMENT INSTRUCTIONS Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Téléviseurs et moniteurs Zenith P42W24B